LumenDimM2micro 2-Channel CRMX or W-DMX Wireless Dimmer

519,00 549,00  *

Available on backorder

Delivery time: 5 - 7 days

The RC4 LumenDimM2micro is a 2-channel CRMX wireless DMX dimmer for LEDs, lamps, and motors in small props, costumes, and more. The inconspicuous circuit-board assembly can easily be hidden in the smallest spaces, even in hair and fabrics.

TWO versions available:

  • with internal antenna
  • with external antenna (included)

SKU: rld2mi-e Categories: , Tags: , , ,

Description

The RC4 LumenDimM2micro is a 2-channel CRMX Lumenradio based wireless DMX dimmer for LEDs, lamps, and motors in small props, costumes, and more. The inconspicuous circuit-board assembly can easily be hidden in the smallest spaces, even in hair and fabrics.

It´s available with internal antenna or external antenna (included in delivery) for range extension. Each micro purchase includes a 6-pin connector with bare wire ends.

RC4 digital persistance iconIt includes 19-bit dimming, which is eight times finer than 16-bit with a whopping 524,000 steps of resolution. The digital persistance for ISL dimming curve simulates the behavior of a tungsten lamp for LED with no visible stepping.

OneTouch

RC4 wireless key featureThe RC4 DMX6dim provides two versatile dimmer outputs.  Like all RC4Magic devices, it includes a built-in radio receiver and uses RC4 OneTouch™ for easy assignment of any DMX channel and dimmer curve to any dimmer with a single press of a single button.

RDM

RDM (remote device management) for RC4 dimmersDevice configuration can also be done with Remote Device Management (RDM) wired or wireless.

Color Match

RC4 wireless key featureIn addition, RC4 ColorMatch™ on the DMX2dim makes it easy to calibrate intensity between two light sources.

PWM

RC4 wireless key featureMany pulse-width-modulation (PWM) dimmers look good to the human eye, but produce banding, blinking, and other anomalies when used with video cameras. For this reason, all RC4 Series 3 dimmers provide multiple PWM frequencies.  Low frequencies are most efficient, ideal for high-wattage incandescent lighting. Mid frequencies improve the appearance of LEDs by eliminating visible strobing in human peripheral vision.  High frequencies eliminate video artifacts.  And finally, supersonic PWM frequencies, though least efficient for power handling, provide PWM dimming without audio interference when used near microphones and electrified musical instruments.

MOTOR CONTROL

RC4 wireless key featureThis dimmer can control the speed and direction of DC motors and the position of hobby servo motors.

For direction control, a second dimmer output can be used to flip a relay that reverses the DC motor connectors – polarity of power directly controls spin direction.

DMX IN/OUT

The LumenDim2micro, and all RC4 Series 3 dimmers, provide a wired DMX data port.  In most cases this port is used to output data to nearby fixtures including fog machines, moving lights, and projector dousers.  The DMX port can also be configured as a DMX input, allowing the LumenDim2micro to be used as a wired dimmer.  In this mode, a comprehensive RDM implementation includes E1.37 dimmer configuration parameters, numerous status sensors (voltage, temperature, current), and each individual dimmer appears as an RDM sub-device.

The internal wireless DMX receiver operates identically to the RC4Magic Series 3 DMXio in receiver mode.  The RC4 DMX miniplug port can used with a range of DMX adaptors, including 3-pin and 5-pin male and female XLR connectors.  The most common adaptor is the RC4DMX5FA with 5-pin female XLR connector.

Connection

A small Amp MTA-100 6-pin connector is provided for connection of power supply and dimmer outputs. Each device is provided with one connector with 6″ (15cm) leads.  Input DC powers both the internal electronics and the connected loads.

Dimmers switch on the negative side of the circuit, ideal for common-anode (common positive) LEDs and LED tape. Dimmer output voltage is precisely the DC power input voltage with no appreciable losses within the 10A peak power handling limit of the device. Continuous running power is limited to 6A due to the safety rating of the Amp MTA-100 connector pins.

Additional information

Weight 0,1 kg
Antenna version

external antenna, internal antenna

Specifications

  • Dimensions: 2.91″ x .779″ x .433″ (75mm x 20mm x 10mm), unenclosed circuit board assembly
  • Weight: 0.40 oz (12g)
  • Connections: Tyco/Amp MTA-100 6-pin
  • Power Input: 6VDC – 35VDC, 0.5W
  • Dimmer Outputs: 2 low-voltage DC dimmers, 19-bit resolution PWM (524,00 steps)
  • Output Power, per Dimmer: 6A non-continuous, 3A continuous
  • Multiple PWM Frequencies: 77Hz (high power), 615Hz (flicker free), 5kHz (artifact free for video), 20kHz (noise free for audio), 40kHz (super-slow-motion video)
  • Multiple Dimmer Curves: Non-Dim, Non-Dim Inverted, Linear, Linear Inverted, Inverse-Square-Law (ISL), ISL inverted, servo motor pulse clockwise (CW), servo motor pulse counter-clockwise (CCW), AC wave (ring telephone bells)
  • DMX Input/Output: RC4 3.5mm mini, USITT DMX512/1990 data, non-standard port, connector adaptors
    available. RDM E1.20 and E1.37 (dimmer configuration) support
  • Wireless DMX Protocol: LumenRadio CRMX or W-DMX
  • RF Antenna: Uses built-in internal chip antenna.
    A version of this product that uses an external antenna is also available.

Downloads

You may also like…

Title

Go to Top